Skip to content

Installing RC2FX ​

The installer downloads official RØDE firmware, adds RC2FX and any saved settings to it on your computer, and flashes the result through the mixer's USB update mode. RC2FX then starts automatically each time the mixer turns on. Installing, updating and repairing all use the same process.

When the app finds a mixer without RC2FX, it offers Install RC2FX. On a mixer that already runs RC2FX, open the installer from Settings › Mixer › Open installer.

Before you start ​

  • Audio stops while the mixer updates, and the update takes a few minutes.
  • Keep the mixer switched on and connected to USB 1 until the installer reports that RC2FX is installed.
  • The computer needs an internet connection to check signed mixer releases, download RC2FX from GitHub, and download the firmware from RØDE.
  • On Linux, the installer asks for administrator access first. Press Grant access and enter your password when the system prompts for it.

Install steps ​

Choose the RØDE firmware version and the RC2FX mixer software to install. The mixer software menu lists signed releases compatible with this app and the chosen firmware. Check the installed and offered versions, press Install… (or Update…), and confirm. Selecting an older version requires an explicit downgrade confirmation.

Firmware profiles are downloaded as signed metadata from GitHub. If a mixer release or firmware profile needs a newer app, the installer shows the minimum version and asks you to update the app first. Without a verified catalog, a download-only build offers no firmware choices.

Normal app builds download mixer software separately. A build made with the optional embedded payload also offers its bundled version as an explicit choice. A failed download never silently substitutes that version. See Versions and updates.

The installer then runs these steps. If a step fails, the installer stops, and Retry continues from that step.

  1. Save settings. If RC2FX is already running, its settings and presets are copied to the computer so the new install keeps them.
  2. Mixer software. The installer downloads and verifies the selected release, including its signature, checksum, and compatibility. On Linux, the administrator helper independently verifies the same release. Previously downloaded files are checked again before reuse. The optional bundled choice is checked locally instead. No mixer changes happen during this step.
  3. Prepare firmware. The installer downloads the chosen version from RØDE, verifies it, and builds a copy with RC2FX and your settings added. The mixer is unchanged at this point.
  4. Switch to USB update mode. The mixer stops audio and shows "Updating via USB". Nothing has been written yet.
  5. Flash firmware. The installer copies the firmware to the mixer and starts the install. Up to this step, switching the mixer off for 30 seconds brings it back on its previous firmware.
  6. Wait for RC2FX. The mixer installs the update and usually restarts three times: to install, to update its internal controllers, and to start normally. Don't touch it during this time. The installer finishes when RC2FX reports that it is running with your settings.

Firmware versions ​

RC2FX supports RØDE firmware 1.7.7 (the default) and 1.7.6. The installer only offers versions whose files have been checked against RC2FX, so a new RØDE release appears only after it has been checked.

Going back to stock ​

Switch to the Stock firmware tab, choose a version, press Flash stock firmware… and confirm. The menu lists the stable and beta firmware RØDE publishes, even versions RC2FX doesn't support yet. This flashes an unmodified RØDE release and removes RC2FX. Your RC2FX settings are saved to the computer first and are restored if you install RC2FX again. The mixer may restart once more afterwards to finish updating its controllers.

To pause processing without removing RC2FX, see Turning RC2FX off.

RØDECaster Duo (experimental) ​

RC2FX can be flashed onto a RØDECaster Duo, but it has not been tested on a real Duo. Flashing or recovery could fail and leave the mixer unusable, and the audio could be wrong or loud. Only try it if you accept that risk.

Duo flashing is off by default. To enable it, turn on Allow experimental Duo flashing in the installer. The app remembers this setting on the computer. Every Duo flash still shows a warning and asks you to confirm with Flash Duo at my own risk.

  • The installer offers only official Duo firmware (1.7.6 and 1.7.7) for a Duo.
  • Back up your RØDE show and unplug headphones and speakers before flashing.
  • Leave the mixer alone after the flash while it updates and restarts.
  • Turning the setting off blocks future Duo flashes but leaves RC2FX on a Duo that already has it. To remove it, use Flash stock firmware… with the setting still on.

The Duo reference lists the channels RC2FX supports on a Duo.

SSH access (developers only) ​

The installer doesn't add SSH access. Developers can turn it on and off without reflashing under Settings › Developer; see Working on a mixer. Installing and using RC2FX don't need it.

Installer files ​

The installer stores downloads, settings backups and a log of every command sent to the mixer in an RC2FX/installer folder inside your user data folder:

SystemUser data folder
Windows%LOCALAPPDATA%
macOS~/Library/Application Support
Linux~/.local/share

Testing status ​

The installer has flashed a real Pro II from Windows and macOS, and RC2FX started afterwards with its settings on Windows. Flashing from Linux has not been tested on hardware, and no Duo has been flashed.