Tips and troubleshooting
Getting good sound
- Run at 48 kHz, the mixer's native rate. On Windows, set the RØDECaster's playback and recording devices to 48000 Hz in the Sound control panel (Advanced tab). At 44.1 kHz Windows resamples, which can cause crackle.
- Use a good USB-C cable. A worn cable can drop USB audio, which sounds the same as crackle from the mixer. Try another cable first when you hear crackle.
- For a voice, a reasonable starting chain is a high-pass at 80 Hz, suppression, a gentle compressor, and a limiter last.
- Noise suppression delays its channel by about 16.5 ms. See Noise suppression.
The app can't find the mixer
- Check that the cable is in USB 1. The app doesn't use USB 2.
- On Linux, check the USB permission rule in Getting started.
- If the app reports more than one mixer on USB, connect only one.
- If the app reports that the mixer is connected but RC2FX isn't running, the mixer is running stock audio. Either RC2FX isn't installed or it has fallen back to stock. Open installer installs or repairs it.
RC2FX stopped processing
When RC2FX detects a problem it falls back to stock until the mixer is next switched on. Power-cycle the mixer to start it again.
If it keeps happening, use Export diagnostics… (in Settings › Diagnostics, or on the error notice) and attach the file to your report.
If the mixer stops responding, power-cycle it.
Audio glitches or crackle
- Rule out the cable and the sample rate (see above).
- In Settings › Diagnostics, turn on Show telemetry and watch the counters and the events window while the problem happens. See Settings and diagnostics.
- If the glitches only happen with noise suppression on, turn off Lookahead, or try another screen conversion setting.
- Turn off Settings › Mixer › Processing. If the glitches stop, RC2FX is the cause. If they continue, the cause is elsewhere.
After a firmware update
The first start after a firmware update, including an RC2FX install, takes longer. The mixer updates its internal controllers and restarts once more. Wait for it to finish before using it.
The mixer forgets its setup at every restart
RØDE keeps the mixer's setup, Wi-Fi, shows and serial number on a settings partition that it mounts at every start. If that doesn't happen, the mixer asks for its initial setup every time, Wi-Fi doesn't stay connected, and the RØDECaster App shows a serial number of zeros. Don't redo the setup while this is happening. It is lost again at the next restart, and the setup you had is usually still on the mixer, unused.
- After installing RC2FX, the installer waits while RC2FX checks the files the flash put on the mixer. If it says it restored some, turn the mixer off and on again; the setup comes back. If it says some are damaged, install again.
- If the installer refuses with "the mixer reports the placeholder serial number", the settings partition isn't mounting and flashing can't fix it, because the update drive lives on that partition too. A developer can repair it; see Repairing a mixer that forgets its setup.
The RØDECaster App's Reset Device erases the mixer's data partition, including SMART pad sounds. Keep copies of your pad sounds before using it.
RØDE's software
RØDE's RØDECaster app and Windows virtual device driver both work while RC2FX is running on USB 1. These two issues also occur on stock firmware:
- If RØDE's app stays on its device list for a minute or more before you select the mixer, it can get stuck on "SYNCHRONIZING DEVICE". Close and reopen the app, then select the mixer straight away.
- If RØDE's virtual devices (Virtual A/B, Game, Music, …) disappear on Windows, check for a browser or other app playing to the raw Main Multitrack device. Closing that app lets RØDE's driver restore them.
Questions
Does RC2FX use my computer's CPU? No. Processing runs on the mixer. The app only edits settings.
Do I need to keep the app open? No. After Save to mixer, the settings are stored on the mixer and persist across restarts.
Does it work with a console, phone or second computer? Yes. Any device that receives audio from the mixer gets the processed audio.
Does a RØDE firmware update remove it? Yes. Updating through RØDE's app installs stock firmware, which removes RC2FX, and RØDE's updater doesn't keep RC2FX's settings. Save a settings file first (Settings › Files › Save…) and open it again after reinstalling. The RC2FX installer saves your settings to the computer automatically.
Can I break my mixer? On the Pro II, the installer uses RØDE's update process and only adds files, and flashing stock firmware removes RC2FX completely. This is still unofficial software with no warranty. Duo support is untested on hardware and carries more risk.