Using the app
Overview
After connecting, the app opens on the Overview. It shows one strip for each fader in your current RØDE show, except SMART Pads, with a live level meter. Headphones and outputs are listed below the faders. Processed channels show the effects they run. Click a strip to edit that channel. Overview at the top of the sidebar, or Esc, returns to this page.
Channels
The sidebar lists the channels you are processing first. The remaining channels follow in groups: Microphones, Sources, Headphones and Outputs. Sources appear only if they are assigned to a fader in the current show. RC2FX does not list or process SMART Pads, and the mixer's pad playback works as before. Settings is at the bottom of the sidebar.
Selecting a channel opens its editor. Audio passes through a channel unchanged until you turn on the Processing switch at the top right of its page. The switch takes effect on the mixer immediately. Turning it off stops processing and keeps the channel's effect settings. You can also set up effects before turning processing on.
Changing the show
Processing settings are tied to a source and follow it between faders.
- Removing an input from the show turns its processing off and keeps its effect settings.
- Moving an input to another fader keeps its processing and effects with that input. The input that takes over the old fader keeps its own settings.
- Adding a removed input back leaves processing off. Turn it on again when you want it.
- Headphones and outputs are unaffected by show changes.
RC2FX acts on a show change only after it reads two matching, complete copies of the show, including at startup. Failed or partial reads change nothing. Once the show is confirmed, processing is turned off for any saved input that is absent, and enabling an absent input is undone. Until the show is confirmed, an input that is still processed may appear under PROCESSED, NOT IN THIS SHOW on the Overview.
Building a chain
A processed channel is shown as a signal chain, read left to right. Effects start switched off.
- Click an effect to open its controls and switch it on.
- Drag an effect onto another to change the order. For example, placing the compressor before or after the EQ changes how it responds.
| Effect | Use |
|---|---|
| High-pass | Cuts rumble, desk thumps and handling noise |
| Noise suppression | Removes background noise from a voice (microphones and Chat Mix Out only) |
| EQ | Shapes the tone, with up to 32 bands |
| Compressor | Evens out loud and quiet passages |
| Gain | Raises or lowers the level |
| Limiter | Keeps peaks below a ceiling |
Effects describes each control. Noise suppression has its own page: Noise suppression.
Saving changes
Effect changes are held in the app until you press Save to mixer in the bar at the bottom of the window. Discard drops them. Saving does not interrupt audio. Settings are stored on the mixer, so processing continues after you close the app or switch the computer off.
If the mixer's settings change from another source while you are editing, such as a second computer, the app shows a notice and asks whether to keep your edits or reload the mixer's settings. If you close the app with unsaved edits, it asks for confirmation first.
Presets and settings files
Settings, at the bottom of the sidebar, contains:
- Presets, stored on the mixer. You can save the current settings as a preset, load one or delete one, for example to switch between a podcast setup and a gaming setup.
- Settings files on your computer, under Files. Open… loads a file into your edits. Save… writes the current settings to a file, for a backup or to copy them to another mixer.
Importing and exporting EQ
The EQ toolbar has Import…, Paste and Export…. Import and Paste accept:
- Equalizer APO and AutoEQ parametric text. AutoEQ publishes corrections for thousands of headphones, which you can paste onto a headphone channel.
- EasyEffects presets.
Export… saves the channel's EQ as an EasyEffects preset.
Importing replaces only the selected channel's EQ. If a file contains more than one equalizer, or a stereo EQ is imported onto a mono channel, the app asks which one to use. EasyEffects Width and Slope fields are ignored on import and left out on export. Steeper slopes (x2–x4) are imported as a single, gentler filter section. Other unsupported settings are rejected with a short explanation.
The EQ curve in the editor is calculated from the settings. It does not reflect the live audio.
Turning RC2FX off
- Settings › Mixer › Processing turns all RC2FX processing off or on again. Your settings are kept.
- The Processing switch on a channel turns off that channel only.
To remove RC2FX from the mixer, see Going back to stock.
The status bar
The bar at the bottom of the window shows how many channels are processed. When something needs attention, such as unsaved changes or a lost connection, the bar shows that instead. Results of actions such as saving, importing or exporting appear as notifications.